Development of suitable ferroelectric nanocomposites in thin film  form for energy applications

Development of suitable ferroelectric nanocomposites in thin film form for energy applications

dc.contributor.advisor	Gayen, Rabindra Nath
dc.creator.researcher	Kadir, Eheta Samul
dc.date.accessioned	2024-07-22T10:32:51Z
dc.date.available	2024-07-22T10:32:51Z
dc.description.abstract	This thesis provides information about the development of highly flexible ferroelectric nanocomposite materials in thin film form and their applications in energy storage, conversion and detection process. Polyvinylidene fluoride (PVDF) is synthesized in flexible thin film form, which is dielectric, ferroelectric, piezoelectric and pyroelectric in nature. A cost effective chemical solution based method is adopted to fabricate PVDF nanocomposite membranes with nanofillers like zinc oxide (ZnO), graphene oxide (GO) and both ZnO and GO loaded into that. PVDF polymer membrane possesses energy density of 11.3 × 104 J/m3 which increases to 65.5×104 J/m3 when ZnO nanoparticles are added to it. Inclusion of GO nanofiller completely destroys its energy density to 0.06 × 104 J/m3. Addition of both nanofillers increases energy density to 61.7 × 104 J/m3. Polarization of PVDF at an external electric field of 15kV/cm is 5.94 μC/cm2 which increases greatly to 15.98 μC/cm2 by ZnO incorporation into it. For tri-phase PVDF/ZnO/GO nanocomposite membrane, the polarization value is 14.14 μC/cm2. A great improvement in dielectric constant is observed from 47 for PVDF to 261 for PVDF/ZnO composite. For PVDF/ZnO/GO composite dielectric constant is 151. Dielectric loss for PVDF is 2.31 which reduce to 0.46 for PVDF/GO. PVDF/ZnO/GO tri-phase composite shows higher open circuit voltage (Voc) and short circuit current density (Jsc) resulting in highest output power delivering composite in different modes like finger tapping, periodic bending and repetitive stretching. PVDF membrane shows responsivity of 0.004 (µA/cm2/W) in presence of solar spectrum at an external bias of 10 V with rise time of 44 sec. Introduction of increasing GO amount upto 15% (v/v) gradually increases the photocurrent to 4.0 µA/cm2 with shorter response time of 21 sec. Further, in mechanically bend condition, all of these composites show higher dark and photocurrent due to formation of piezo-potential. Impedance spectroscopic study is conducted to gain proper insight of these occurrences along with effect of filler inclusions. Also, effect of external stimuli like mechanical stress and light irradiation on those composites are explained from the changes in various parameters obtained from the fitting of Nyquist plots drawn from impedance spectroscopic measurements.	en_US
dc.description.searchVisibility	true	en_US
dc.format.mimetype	application/pdf	en_US
dc.identifier.uri	https://www.presiuniv.ac.in	en_US
dc.identifier.uri	http://www.presiuniv.ndl.iitkgp.ac.in/handle/123456789/2408
dc.language.iso	eng	en_US
dc.rights.accessRights	authorized	en_US
dc.source	Presidency University	en_US
dc.source.uri	https://www.presiuniv.ac.in	en_US
dc.subject	PVDF	en_US
dc.subject	Composite	en_US
dc.subject	ZnO	en_US
dc.subject	Polymer	en_US
dc.subject	Ferroelectric	en_US
dc.title	Development of suitable ferroelectric nanocomposites in thin film form for energy applications	en_US
dc.type	text	en_US